It’s an exciting day today! I've passed 5,000 pageviews on my blog (5,146 to be exact). That means if I’d let Google put ads on there
they would have paid me about $1 so far! I also found out I've been working on the car so long that the people at Ace Hardware know me by name. I'm not sure that's a good thing. More interesting though is that the place I work for just announced they’ll
have their third “Bring Your Ride to Work” day 4 weeks from today. I've dreamed about bringing a vehicle in
since the 1st annual BYRTW day (which was about 6 years ago), but
always ran into problems actually getting my vehicle in to work. The first year I was planning to take my 64
CJ6 in but a nut stripped out inside the transfer case 100 feet from my house
the day of the event. The second time I
planned to bring in the CJ again after finishing the power steering conversion
on it, but the steering wobble I was trying to correct with the conversion
reappeared 5 days prior to the event. So
now I’m faced with a new challenge: getting my Porsche roadworthy in less than
28 days! Here’s what I’m up against. We’ll start with stuff I've recently finished.
Months ago I completely took apart the interior with the
intent of restoring the dashboard. Well,
I got the dash 98% complete and never finished it off or put anything
together. Two days ago I decided it was
time to put it all back, and amazingly it only took 4-5 hours to do! And it looks fantastic with the new dash in
place. What the heck was I waiting
for?! Now all I’m missing is the
passenger seat. Sorry, no pics...
Another outstanding part of the system is the vacuum needed
to work the brake booster. For those of
you that don’t know, a normal gas engine provides vacuum when it sucks air into
the intake. Historically, this vacuum
has been used for all sorts of things like emissions control, crankcase ventilation,
cruise control, wiper blade operation, and of course, brake assist. Since the engine is long gone, I need a
dedicated pump. A lot of EVers use a
piston pump because they must be already commercially available. My friend, Joe, has one of these on his car
and the only gripe about it is it’s so dang loud! In fact, it’s the loudest thing on the whole
car.
By chance, I ran across a rotary vane pump on www.surpluscenter.com that may do the
trick. The benefit of a rotary vane pump
is they tend to be quieter. After
finding the product data sheet on it, it appears to have very similar
characteristics to Joe’s piston pump, so I’m gonna give it a try. I also found an automotive fan motor in there
and a jaw coupling for a grand total of about $50 (which is about $200 less
than any piston pumps I've found) that I just need to mount together. And here it is!
Now I get to find out if this $50 was a waste or not. I hooked it up to the brake booster and let
it run for a few seconds before pumping the brake pedal. And it’s definitely working! After turning it off, I can tell the force to
push the pedal is going up after 2 pumps or so.
Only problem is I’m not sure it’s any quieter than Joe’s is. But luckily when I’m showing it off to Joe,
by chance we figure out that if you baffle the inlet it’s actually super quiet! Win win.
Okay, so here’s what I have left to do:
-
Mount the vacuum pump
-
Mount the coolant pump
-
Mount the coolant reservoir
-
Mount the coolant heat exchanger (heater core)
-
Plumb the coolant lines
-
Finish the battery racks
-
Adjust the motor coupler
-
Order batteries
-
Do a heck of a lot of wiring
-
New tires
-
Alignment
-
Get Insurance and temp registration
-
Complete the charger
Doh! The charger is not mature at all. In fact, it’s still in schematic mode. That’s certainly going to be the long pull,
but luckily I have a backup plan. Joe
has a mini-charger that I can use. It’d
be a huge pain to recharge since I’d probably have to disassemble the whole
battery pack, but that may be my only option.
Well, what am I doing here wasting time on the
computer? I’d better get out there and
start working! Only 27 days left and a lot to do!
No comments:
Post a Comment